FAAC Gate Motor & Opener Nationwide

FAAC Gate Motor & Opener in Agoura Hills: What to Know First

FAAC gate motor repair and replacement in Agoura Hills is what we do week in and week out. As an independent FAAC service provider, we repair, rebuild, and install these openers across the Conejo Valley, with most jobs done in a single visit and every job protected by a written 90-Day Done Right Promise. If your FAAC opener is dead, grinding, or halfway open at 7 a.m. on a school day, call (213) 293-3886 and a live person answers, not a voicemail.

Call (213) 293-3886

This page is for Agoura Hills homeowners with a FAAC swing or slide gate that has stopped behaving. You want to know what is wrong, what it costs, and whether the fix will last. That is exactly what our crews deliver, with the price settled before we turn a single bolt.

How FAAC Products Fail - and How We Fix Them

FAAC builds a solid operator. But every brand has its habits, and after nearly three decades of working on them in this valley, we know where FAAC units tend to give up first.

• Capacitor failure on the 400 and 402 swing operators. This is the most common FAAC failure we see in Agoura Hills, and it usually shows up as a gate that hums but will not move, or moves an inch and stops. The start capacitor dries out over time, especially with the heat cycles we get off the 101 corridor. The fix is a capacitor swap, not a whole new motor, and we carry the right values on the truck.
• Limit switch drift on the 844 slide series. A slide gate that overshoots the closed position, then reverses and stops short, is typically a limit switch issue. On the 844, the magnetic limit cams can loosen over years of daily cycles. We re-secure and recalibrate, and where the switch itself is worn, we replace it with an OEM part rather than gambling on an aftermarket unit that triggers false stops.
• Oil weeping from the hydraulic 770 and C720 models. These hydraulic operators run for decades when maintained, but the seals harden with age. A small oil stain under the operator housing is the tell. Caught early, it is a seal kit and fresh hydraulic fluid. Ignored, the pump runs dry and the repair cost triples. In the dry, dusty air around Ladyface, dust accelerates seal wear, so we recommend a quick visual check during our seasonal tune-ups.
• Photocell misalignment on any FAAC rig after a hard wind or a bump from a delivery truck. The gate refuses to close, or reverses for no apparent reason. Before assuming the board is bad, we check the photocell alignment, the mounting bracket, and the wiring at the terminal block. In many cases, the fix is ten minutes of adjustment, not a parts order.
• Control board lockouts after power flickers in the Santa Monica Mountains. FAAC boards are generally robust, but a brownout or repeated quick outages can leave the board in a fault state. We reset and verify the full safety circuit before restoring operation. Where a board is truly fried, we quote an OEM replacement before any money is spent.

Our FAAC Gate Motor & Opener Process

Here is how a FAAC gate motor job goes from your first call to a gate that closes like it should:

1. 1
   You call, a human answers. We ask what the gate is doing, what model you have if you know it, and when you need it addressed. If it is an emergency, we tell you honestly how soon we can get there.
2. 2
   We diagnose before we touch a thing. Victor Salinas and the crew check the operator, the arm or piston, the safety edges, the photocells, the power supply, and the ground. We tell you exactly what we found and what it needs. If it needs less than you feared, we say so.
3. 3
   We price it before we start. You get a written number. No open-ended labor, no surprise upcharge at the end. If you want a second opinion on an estimate from another company, we do those free.
4. 4
   We do the work with the right parts. On FAAC jobs, we use OEM parts whenever the repair touches the safety circuit, the board, or anything that keeps the gate from becoming a hazard. We will use a quality aftermarket part when it is a non-safety item like a hinge bushing or a cover, and we will tell you the difference and the price on both.
5. 5
   We test the whole system, not just the part we replaced. The gate cycles a dozen times under load. We check the force settings, the photocells, the safety edges, and the manual release. We check for pinch points and obstructions.
6. 6
   We leave you with a written 90-Day Done Right Promise. If anything we touched is not right, we come back and make it right. No paperwork, no arguing.

What FAAC Gate Motor & Opener Costs in Agoura Hills

We will not give you a hard price without seeing the gate, but here are honest ranges for FAAC work in this area:

• FAAC capacitor replacement (400/402 series): $130-$220 installed, including the service call.
• Limit switch repair and recalibration (844 slide series): $180-$340 depending on whether the switch needs replacing or just remounting.
• Hydraulic seal kit and fluid service (770/C720): $320-$580. This includes fresh fluid and a full system check.
• Control board replacement: $450-$850 for the board and labor. OEM board cost drives most of that range.
• Complete FAAC operator replacement (swing or slide): $2,500-$5,800 installed, depending on the model, the operator type, and what we can reuse from the existing install.

What moves the price on FAAC gate motor and opener work is parts cost, access to the operator, the age of the gate structure itself, and whether the safety circuit needs updating to current standards. We quote the job before we start, and that number is the number. Call (213) 293-3886 for a free estimate.

Why Agoura Hills Homeowners Call Ironworks Gate Co. for FAAC Work

Because we have been at this for over 42 years, and we plan to be here for another forty. Victor Salinas grew up in the Ladyface foothills, learned the trade at Los Angeles Pierce College in Woodland Hills, and has spent the better part of three decades fixing gates across Agoura Hills and the Las Virgenes Valley. The technicians who show up at your driveway are background-checked and uniformed, and they work in your home the way they would work in their own mother’s.

We service nine gate-automation brands, so if your property has a FAAC on one gate and a LiftMaster, Mighty Mule, Ghost Controls, or DoorKing on another, one call sorts the whole driveway. Every job carries the 90-Day Done Right Promise, in writing. And a live person answers our phone 24 hours a day, 7 days a week. When a gate fails at 6 p.m. on a Friday, you talk to a person who knows gates, not a machine.

If it rolls or swings, we can sort it out, and we will tell you exactly what we found before we touch a thing.

FAQs